661
ALARM SYSTEM
This remote control alarm is operated by multi code remote control. Entry point protection of doors, boot and bonnet with a shock sensor. Audible warning is achieved via a standard 115dB siren, visually via the vehicle indicators and via a dash mounted high intensity red LED. The system may provide keyless entry and a source of immobilisation
- Arming procedure while ignition is off
The system will arm immediately if the main button of a valid remote control is momentarily pressed, the doors will lock and all security functions will become active 
- Disarming procedure
The system will disarm when the main button of a valid remote control is pressed
- Immobilisation Circuit
The system features a 30 Amp rated, normally closed immobilisation circuit, which breaks engine critical signals in the vehicle. Starter motor, fuel pump, fuel injection, main ignition are commonly immobilised circuits
- Safety circuitry in case of power failure
System sources alternate power from ignition if main power is lost
- Component protection against harsh road conditions
All relays are fully encapsulated to provide protection against dust and moisture
- System memory
Allows system to track two controllers
- Controller re-programming
Service technician can delete lost or stolen controllers from memory
- Plug and play for service
Designed to allow easy access for service technicians. Plugs and sockets are located inside the main control module to protect against access by thieves
- Emergency Personal Identification Number (PIN) override
Enter the secret two digits to override the immobiliser 
- Alterable PIN
A factory programmed PIN comes standard with each system. It is recommended the owner of the system changes the PIN to a new, easily remembered number
- Super bright red dash LED
This LED flashes to inform user when system is armed. The LED is mounted on the driver's side dash and is visible from outside the window
- Arm/Disarm confirmation
System flashes car indicators when arming or disarming
- Alarm illumination
System flashes car indicators when thief triggers alarm
- Trigger diagnostics
System will flash indicators to report the last triggered circuit
- Standard siren
Uses standard two wire 115dB siren
- Arm/Disarm confirmation
System sounds a siren when arming and disarming
- Temporary arm/disarm chirp disable
Momentarily press the second button of the remote control before pressing the main button, the siren will not chirp during that one operation
- Doors, bonnet and boot monitoring
Triggers alarm system if intruder opens any protected entry point in vehicle
- Accepts plug-in single stage shock sensor
Sensor measures vibration subjected to vehicle to detect intruder, SEN-002.
- Locks and unlocks all doors
System can trigger factory central locking, aftermarket central locking or central locking relays 
- Variable pulse time
Extend pulse length to drive pneumatic central locking systems (Mercedes)
- Automatic re-locking
System will re-arm and re-lock doors if previously disarmed by remote control and doors remain closed
- Anti-hijacking protection
System locks doors when ignition is turned on, unlocks when ignition is turned off
- Current draw
<10mA average while armed
<150mA disarm (and for no more than 39 seconds after ignition is switched off)
- Wide Operating voltage
Operating voltage +9VDC to +15VDC
- Operating temperature
-20 degrees to +85 degrees for equipment designed to be installed within vehicle cabin
- Operating temperature
-20 degrees to +105 degrees for equipment designed to be installed inside engine compartment
- Polarity protection
The system circuitry is design to protect itself against accidental battery polarity reversal. This can happen when replacing the vehicle battery
- Independent indicator power fuse
System uses independent fuse to power indicators, ensures short circuit in indicator circuit does not affect system operation
- Short circuit protection
The power supply wire to the system is protected against an internal fault within the system
- Panic / Car Finder
Press and hold second button of remote control to cause siren to sound and indicators to flash
- Electric window closer
Provides signals used by electric window closers, system will close all electric windows when armed by remote control
- Electronic boot release
Press and hold the secondary remote control button to activate boot release output. The indicators will flash four time each time the boot release signal is sent 
- Installation Guide
Complete installation guide and specifications for the 661-3(NWH).
- Installation Guide
Complete installation guide and specifications for the 661-3.
- Installation Guide
Complete installation guide and specifications for the 661.
- User Guide
Informs the end-user of the system's functions, features and limitations. Open - User guide.
- Manufacturers warranty on Control module
Guarantees control module is free from manufacturing defects for 24 months from time of purchase 
- Manufacturers warranty on Sundry items
Guarantees remote controls, siren and sundry items are free from manufacturing defects for 12 months from time of purchase
- Manufactured in ISO9001 facility
Built within world standard production facility
Legend:
Will categorically need extra hardware and connections.
May require additional hardware or connections.
Additional relay and connection required in vehicles with boot solenoid. Relay and solenoid kit required for vehicle without solenoid.
Vehicle circuit polarity may require addition components to convert voltage.
Special order required - this is not part of the standard hardware.
Special feature out of Dynamco's control.
Conditions apply.
Programmable option.
Due to model and manufacturer variations, specifications of actual product may differ from those shown.
Conditions apply.
Programmable option.
** Product images are for illustration purposes only. Actual appearance may vary slightly without notice.
Product Catalogue