OEM UPGRADE ALARM SYSTEM
In addition to the enhancements to the standard P485, Dynamco has upgraded the OE Upgrade to incorporate CAN-BUS network traffic decoding. Making the system compatible with many European car designs
- Proudly Australian
Designed and engineered in Perth, Western Australia
- Arming procedure while ignition is off
The system will arm immediately when the lock button of the remote control supplied by the car manufacturer is pressed
- Disarming procedure
Press the unlock button of the remote control supplied by the car manufacturer
- Auto Arming
System will auto-arm only if the car has a automatic re-locking feature
- Dual Immobilisation Circuits
The system features two independent 30 Amp rated, normally open immobilisation circuits, which break engine critical signals in the vehicle. Starter motor, fuel pump, fuel injection, main ignition are commonly immobilised circuits
- Safety circuitry in case of power failure
System sources alternate power from ignition if main power is lost
- Third circuit of immobilisation (optional)
Additional immobilisation circuits can be added to conform with insurance company requirements
- Component protection against harsh road conditions
All relays are fully encapsulated to provide protection against dust and moisture
- Security wiring
All cables extending from the control module are black and same diameter. Identifying wire tags are removed by the installer during installation of the system
- Plug and play for service
Designed to allow easy access for service technicians. Plugs and sockets are located inside the main control module to protect against access by thieves
- Security housing
Connector plug is enclosed within module case to prevent access by thief
- Stealth wiring
Cutting any immobilisation wiring will still leave the car secure. Bypassing security is not possible by simply removing the system from the vehicle
- Emergency Personal Identification Number (PIN) override
If the valid controller are lost, stolen or broken, the user by over-ride the system by enter the secret four digits via the ignition switch
- Alterable PIN
A factory programmed PIN comes standard with each system. It is recommended the owner of the system changes the PIN to a new, easily remembered number
- High security keys and lock
Disable siren sound when vehicle is taken in for service
- PIN card
A record of the factory programmed override PIN is supplied on handy wallet sized card
- Super bright red dash LED
This LED flashes to inform user when system is armed. The LED is mounted on the driver's side dash and is visible from outside the window
- Arm/Disarm confirmation
System flashes car indicators when arming or disarming
- Alarm illumination
System flashes car indicators when thief triggers alarm
- Trigger diagnostics
System will flash indicators to report the last triggered circuit
- Large battery backup siren
AS/NZS 3749.1:2003 Class A approved 115dB siren, sounds even if battery terminals are disconnected from vehicle battery
- Negative siren output
Can be used to trigger car horn relay or siren
- Arm/Disarm confirmation
System sounds a siren when arming and disarming
- Doors, bonnet and boot monitoring
Triggers alarm system if intruder opens any protected entry point in vehicle
- False alarm prevention
All circuits detected as triggered when arming system will automatically be isolated until trigger resets
- Sensor sockets
Compatible sensors plug straight into main pcb
- Audio glass breakage detection
Uses the sound of the breaking glass to trigger (not vibration) GBS-4XR.
- Accepts plug-in Ultra-sonic sensor
Sensor produces a 40KHz sound wave and measures echo to detect intruder, ACC-001.
- Accepts plug-in single zone microwave sensor
Sensor produces a microwave field to detect intruder, ACC-003.
- Accepts plug-in dual zone microwave sensor
Sensor produces two microwave fields, exterior field to sound siren as warning, interior to trigger alarm in full, ACC-004.
- Accepts plug-in single stage shock sensor
Sensor measures vibration subjected to vehicle to detect intruder, SEN-002.
- Accepts plug-in two stage shock sensor
Sensor measures two levels of shock, soft shock to sound siren as warning, heavy shock to trigger alarm in full, SEN-006.
- Compatible with tilt sensor
Sensor measures vehicle angle with respect to earth, triggers if angle changes - no response to vibration SEN-004.
- Millivolt or Voltage drop protection
Alarm monitors battery voltage, triggers if voltage drop due to courtesy light switched from off to on (opening boot etc)
- Current draw
<10mA average while armed
<250mA disarm (and for no more than 39 seconds after ignition is switched off)
- Wide Operating voltage
Operating voltage +9VDC to +15VDC
- Operating temperature
-20 degrees to +85 degrees for equipment designed to be installed within vehicle cabin
- Operating temperature
-20 degrees to +105 degrees for equipment designed to be installed inside engine compartment
- Polarity protection
The system circuitry is design to protect itself against accidental battery polarity reversal. This can happen when replacing the vehicle battery
- Independent indicator power fuse
System uses independent fuse to power indicators, ensures short circuit in indicator circuit does not affect system operation
- Suitable for models of these manufacturers
Audi, Alfa Romeo, BMW, Chrysler, Ford, Holden, Honda, Hyundai, Kia, Landrover, Mazda, Mercedes, Mitsubishi, Nissan, Peugeot, Proton, Renault, Subaru, Suzuki, Toyota, Volvo & VW
- Short circuit protection
The power supply wire to the system is protected against an internal fault within the system
- Electric window closer
Provides signals used by electric window closers, system will close all electric windows when armed by remote control
- Full diagnostic report
Remove and insert main power fuse to receive report of last three triggers
- Installation Guide
Generic instructions on how to fit the system, it's features and limitations. Open 4WAY version.
- User Guide
Informs the end-user of the system's functions, features and limitations. Open - User guide.
- Manufacturers warranty on Control module
Guarantees control module is free from manufacturing defects for 24 months from time of purchase
- Manufacturers warranty on Siren
Guarantees siren is free from manufacturing defects for 12 months from time of purchase
- Australian Standard for Intruder alarm systems - Road vehicles - Performance requirements
AS/NZS 3749.1:2003 Class A - Australian Standards website.
- Manufactured in ISO9001 facility
Built within world standard production facility
- AS/NZS 3749 sundry standards of compliance (or parts thereof)
AS1217 - Acoustics - Determination of sound power levels of noise sources
AS1259 - Acoustics - Sound level meters
AS1939 - Degrees of protection provided by enclosures for electrical equipment (IP Code)
AS3350 - Safety of household and similar electrical appliances
AS4268 - Radio equipment and systems - Short range devices
AS/NZS3749 - Intruder alarm systems - Road vehicles
AS/NZS61000 - Electromagnetic compatibility (EMC)
CISPR 22 - Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement
ASTM B117 - Standard practice for operating salt spray (fog) apparatus
ISO512 - Road vehicles - Sound signalling devices - Technical specifications
ISO7637 - Road vehicles - Electrical disturbance by conduction and coupling
IEC61000 - Electromagnetic compatibility (EMC)
Will categorically need extra hardware and connections.
May require additional hardware or connections.
Additional relay and connection required in vehicles with boot solenoid. Relay and solenoid kit required for vehicle without solenoid.
Vehicle circuit polarity may require addition components to convert voltage.
Special order required - this is not part of the standard hardware.
Special feature out of Dynamco's control.
Due to model and manufacturer variations, specifications of actual product may differ from those shown.
** Product images are for illustration purposes only. Actual appearance may vary slightly without notice.